Each of these has a layer mask associated with it that allows us to draw on only one side of the page at a time. Look in the Layers palette and you will see that there are two folders there, one named “Left Page” and one named “Right page”. When you first open the combined pages, you may see that one of the sides has a purple color over it, as shown in the following screenshot. Open the two-page spread to start working on it. Note that pages 2 and 3 are now one continuous spread. Once your pages are combined, they will look like the pages in the following image. Click on OK to start the combining process. I did uncheck the “Delete layer with no drawing” option from the Combine pages options because I wanted to preserve the blank layers that were created when the file was made. For publishing to the web you don’t really have to worry about them. The Align Crop Mark and Gap options are only needed if you will be printing these pages to a book. (Note that this really means you can’t hit Undo and immediately split the pages again, you will have to use the “Split pages” option that is listed underneath the Combine pages option in the image above to separate the pages again) You will then see the following message telling you which two pages will be combined and that this operation cannot be undone. Then either go to Story - Combine pages or right-click on the selected page and select “Combine pages” from the pop-up menu, shown below. To do this, click on one of the pages you want to combine into a spread to select it. Let’s combine pages 2 and 3 into a single spread. However, they are two individual pages at the moment. ![]() Notice that pages 2 and 3 are shown together on the same “tile”, this is because they are pages that will be facing one another when the pages are put into a book. Let’s take a look at the four-page file I just created in the screenshot below. ![]() But what if you’ve already created your file and you just want to combine a certain set of pages? No problem! It’s very easy to do! If you want every set of facing pages to be a two-page spread, you should check the option marked by the white arrow in the screenshot above. You also must use the “Page by Page” setting for View instead of the WEBTOON option. This is because a two-page spread can only be made of a left-facing and right-facing page, and the first and last page of a book are single pages. To create a two-page spread you must have AT LEAST 4 pages in your file. You will need to set the number of pages. ![]() If not already, click the box to the left of the Multiple pages option to turn this setting on. These are located in the red rectangle in the screenshot below. Once your page dimensions are entered, scroll down in the New file settings to find the Multiple pages options. Below is a screenshot of the settings I’ll be using for this article. Use your favorite preset or enter in the dimensions you want to create your pages at. Go to File - New, hold down Ctrl+N, or click the “New” icon in the Command Bar to bring up the New file settings. We’ll cover both ways of doing this, but first let’s start making our new file. It is possible to create two-page spreads from only certain pages in your file or to make every set of left and right pages into spreads through the entire file. You can make two-page spreads in CSP Pro, but it’s much harder because you will have to figure out the dimensions of your combined pages and set up the inner margins (the “gutter”, which is where the pages of a book are glued into the book’s spine in the middle) on your own. In this article we will cover the following topics:Ĭreating two-page spreads is very easy when using Clip Studio Paint EX, thanks to the ability to make files with multiple pages. With Clip Studio Paint EX, it is very easy to create either one two-page spread in a comic story or to set up a book file where each set of pages is a two-page set, allowing you to work on two pages at one time. ![]() Whether you’re showing off a fantastic castle in the clouds or showcasing a big action set-piece, they add some “WOW!” to your story. Two-page spreads are a great way to add drama to a comic story. I write weekly posts on and on CSP Tips, so be sure to come back every week to learn more Clip Studio Tips and Tricks from me! Many of you probably know my name from those books, in fact. I was a beta-tester on the Manga Studio 5 program and for Clip Studio Paint, and I have written three books and several video courses about the program. Hello! My name is Liz Staley and I’m a long-time user of Clip Studio Paint (I started using the program back when it was known as Manga Studio 4!).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |